|
PIB07-01 |
Global Positioning System (GPS) and Established Surface Stations or Markers - 01/18/2007 |
|
PIB07-02 |
Potential for the Quick Start Candle on Mine Safety Appliances Life-Saver 60 Self-Contained Self-Rescuer to Overheat or Catch Fire on Units Manufactured from September 1, 1999 through December 31, 2004 - 01/19/2007 |
|
PIB07-03 |
Implementation of Section 2 of the Mine Improvement and New Emergency Response (MINER) Act of 2006: Options for Providing Post-Accident Breathable Air to Underground Coal Miners. This Program Information Bulletin should be used in conjunction with Program Policy Letter No. P06-V-10 |
|
PIB07-05 |
The Danger of Oxygen Deficiency in Underground Coal Mines |
|
PIB07-06 |
Guy Wires of Poles Supporting High-Voltage Electric Power Lines |
|
PIB07-07 |
MSHA Evaluation of Non-MSHA Product Safety Standards for Explosion-proof Enclosures |
|
PIB07-08 |
Potential Hazard to Roof Bolting Machine Operators Due to Inadvertent Control Actuation |
|
PIB07-09 |
Single Source Coal Reporting Pilot Program |
|
PIB07-10 |
Notification of withdrawal of MSHA and NIOSH approval for Mine Safety Appliances (MSA) Flow-Lite Sampling Pumps |
|
PIB07-11 |
Examination of Electrical Underground Coal Mine Equipment |
|
PIB07-12 |
Best Practices for Turning Crosscuts with Remote Controlled
Continuous Mining Machines; Reissue of P-03-28 |
|
PIB07-13 |
SCSR Inventory and Report |
|
PIB07-14 |
Fastenings Used for Joints of Flame-Arresting Paths on Intake or Exhaust Systems for Permissible Diesel-Powered Equipment |
|
PIB07-15 |
Potential Safety Hazard on Permissible Mobile Diesel-Powered Transportation Equipment with Sandvik (formerly EJC Mining Equipment, Inc.) Wet Scrubber Systems (PDF only) |
|
PIB07-16 |
Hard Hats - Revised |
|
PIB07-17 |
Test Procedure for Evaluating Maximum Total Exhaust System Backpressure on an Underground Diesel-Powered Machine |
|
PIB07-18 |
Maximum Total Exhaust System Backpressure Specification Increase for Caterpillar Inc.'s (Caterpillar's) 3304 PCNA and 3306 PCNA Diesel Engines |
|
PIB07-19 |
Hazards of Sliding Table Masonry Saws |
|
PIB07-20 |
Change to Respirable Dust Data Card - Addition of Pre-weight Date |
|
PIB07-21 |
Clarification of Requirements of Conveyor Start-Up Warnings for §§ 56.14201 and 57.14201
|
|
PIB07-22 |
Operation of Continuous Haulage Systems |
|
PIB07-23 |
Updated Test Questions for Certifying Individuals to Perform Dust Sampling and Maintenance and Calibration of Approved Sampling Equipment |
|
PIB07-24 |
Use of Portable Roof Drills |
|
PIB07-25 |
Potential Hazardous Condition Caused by Bolts Breaking on X/P-1628 Electric Motors |
|
PIB07-26 |
Charging of Lithium Ion or Lithium Polymer Batteries |
|
PIB07-27 |
General Monitors Model 420, 420d, S500, and S800 Machine Mounted Methane Monitoring Systems |
|
PIB07-28 |
Updated Test Questions for Certifying Individuals to Perform Dust
Sampling and Maintenance and Calibration of Approved Sampling Equipment (Amended) |
|
PIB07-29 |
Breaching and Drilling into Sealed Areas |
|
PIB07-30 |
Notification of Opportunity for Interested Parties to Comment on Advance Draft of Updated "Engineering and Design Manual: Coal Refuse Disposal Facilities" |
|
PIB07-31 |
Use of Fall Protection In, Around, or Over Any Shaft and Conveyance
Safety Measures
|
Back to Top