skip navigational links http://www.dol.gov www.msha.gov United States Department of Labor
A to Z Index | Find It! in DOL |            [skip navigational links]     Search MSHA's Website   Search MSHA
 
Printer Friendly Version
U.S. Department of Labor          


 Mine Safety and Health Administration
1100 Wilson Boulevard
Arlington, Virginia 22209-3939                    		 Department of Labor Logo


EFFECTIVE DATE:   September 10, 2009 EXPIRATION DATE: 03/31/2011


PROGRAM POLICY LETTER NO. P09-V-10



FROM:          KEVIN G. STRICKLIN  KEVIN G. STRICKLIN
                    Administrator for
                    Coal Mine Safety and Health

SUBJECT:      Remote Restarting of Conveyor Belts when a Slip Switch
                     Stops the Belt

Scope
This Program Policy Letter (PPL) applies to underground coal mine operators, Mine Safety and Health Administration (MSHA) enforcement personnel, and other interested parties.

Purpose
The purpose of this PPL is to provide guidance to the mining industry and enforcement personnel on the purpose of slippage switches required on belt conveyors under 30 C.F.R. § 75.1102.

Policy
The function of the slippage switch required under 30 C.F.R. § 75.1102 is to stop the belt when the speed of the drive roller is different from the speed of the belt which may cause the belt to slip causing friction and overheating and creating a fire hazard to personnel. The American Geological Institute and the U.S. Bureau of Mines define a belt slip as "the difference in speed between the driving drum and the belt conveyor." A Dictionary of Mining, Mineral, and Related Terms 47 (2d ed. 1968). When that action takes place, the slippage switch is designed to automatically stop the belt to prevent overheating and ignition of the belt.

Belt slippage can be temporary and may not be excessive. This condition can be caused by a fall of material on the belt which would slow down the belt and cause a slight slippage. Some mines are restarting the belt remotely from the surface using a Programmable Logic Controller (PLC). The safest method of addressing a belt slippage condition is to physically go to the location where the slippage occurred, examine the belt and restart the belt at that location. However, MSHA believes that remote restarting of conveyor belts can be safely accomplished under controlled conditions. For States that permit usage of PLCs to start the conveyor belt from the surface, and to ensure that this practice is not taking place when an actual slippage condition occurs, remote starting of conveyor belts should be used only under controlled conditions. The following are examples of controlled conditions:
  • Install an audible and visible alarm circuit along the belt entries to warn miners underground that the belt is restarting.


  • Install a locking device in the PLC circuit to allow only one attempt to restart the belt from the surface. If the belt does not start the condition should be checked and the belt should be restarted locally.


  • Incorporate additional safety circuits in series with the belt slip switch timer to ensure that the conveyor belt is not in an actual slip condition. These additional safety circuits consist of a revolution per minute (RPM) switch on the main drive pulley which will shut the belt down in a few seconds (4 to 7 seconds) if it senses a high rpm on start-up.


  • Install a safety device on the motor circuit to monitor the rate of current increase. If the motor current does not indicate an inrush high current for motor start-up, it will shut down the conveyor belt in a few seconds versus the 2 to 3 minutes usually allowed by the belt slip timer.


  • Provide a lockout circuit to prevent restarting of the belt by the PLC if the RPM switch activates indicating high RPM or inrush high current is detected on start-up, so that the circuit could not be restarted without someone going to the drive.


  • Install live cameras at locations that will assist the person operating the remote start-up.


  • Train miners on safeguards that should be in place to remotely start a belt under controlled conditions.
Background
MSHA is aware that some mines are using a PLC to remotely restart conveyor belts from the surface or other remote locations after they detect a belt slippage condition without viewing the belt to determine the problem and correcting it if necessary. Running a conveyor belt when a slippage condition exists could cause friction and overheating, posing a fire hazard to miners.

Authority
The Federal Mine Safety and Health Act of 1977, as amended, 30 U.S.C. § 801 et seq.; 30 C.F.R. § 75.1102.

Filing Instructions
This PPL should be filed behind the tab marked "Program Policy Letters" at the back of Volume V in the Program Policy Manual.

Internet Availability
This PPL may be viewed on the Internet by accessing MSHA home page (http://www.msha.gov) and then choosing "Compliance Assistance," "Compliance Info" and "Program Policy Letter."

Issuing Office and Contact Persons
Coal Mine Safety and Health, Safety Division
Salwa El-Bassioni, (202) 693-9525
E-mail: el-bassioni.salwa@dol.gov

Distribution
MSHA Program Policy Manual Holders
MSHA Special Interest Groups
Underground Coal Mine Operators




Back to Top   Back to Top www.msha.gov www.dol.gov
Frequently Asked Questions | Freedom of Information Act | Customer Survey
Accessibility | Privacy & Security Statement | Disclaimers
Mine Safety and Health Administration (MSHA)
1100 Wilson Boulevard, 21st Floor
Arlington, VA 22209-3939		 Phone:    (202) 693-9400
Fax-on-demand: (202) 693-9401
Technical (web) questions: Webmaster
On-line Filing Help: MSHAhelpdesk@dol.gov
or call (877) 778-6055
Contact Us