Skip to main content
U.S. flag

An official website of the United States government.

Petition - Docket No. 2003-002-C

Petition for Modification


In the matter of
Ken American Resources Inc.
Paradise No. 9 Mine
I.D. No. 15-17741
Docket No. M-2003-002-C
30 CFR 75.1909(b)(6) 

PROPOSED DECISION AND ORDER


On January 7, 2003, a petition was filed seeking a modification of the application of 30 CFR 75.1909(b)(6) to Petitioner's Paradise No. 9 Mine located in Muhlenburg County, Kentucky. The Petitioner proposes an alternative method outlined in the petition that will at all times guarantee no less than the same measure of protection afforded by the standard. 

MSHA personnel conducted an investigation of the petition and filed a report of their findings and recommendations with the Administrator for Coal Mine Safety and Health. After a careful review of the entire record, including the petition and MSHA's investigative report and recommendation, this Proposed Decision and Order is issued. 

Finding of Fact and Conclusion of Law


Section 75.1909(b)(6) provides that all self-propelled non-permissible diesel-powered equipment must have, in addition to all other requirements, service brakes that act on each wheel of the vehicle such that failure of any single component, except the brake actuation pedal or other similar actuation device, must not result in complete loss of service braking capability. 

Petitioner proposes an alternate method in lieu of the front wheel brakes on the DAPCO, Serial No. 001 grader powered by a Deutz diesel engine Model #BF4M1012EC used at the Paradise No. 9 Mine, which has 6 wheels. Petitioner proposes to limit the speed of the diesel graders to 10 miles per hour (mph) and to train the grader operators in the proper techniques for lowering the blade to provide additional stopping capability in emergency situations. 

The alternative method proposed by Ken American Resources Inc. (as amended by the recommendations of MSHA) will at all times guarantee no less than the same measure of protection afforded the miners under 30 CFR 75.1909(b)(6). The diesel graders will be equipped with devices which limit speed to 10 mph and the grader operator(s) will be trained to lower the blade in emergency conditions to stop the grader. These terms and conditions will provide an equivalent level of safety to the standard requirement that each wheel of the grader be equipped with service brakes. 

On the basis of the petition and the findings of MSHA's investigation, Ken American Resources Inc. is granted a modification of the application of 30 CFR 75.1909(b)(6) to its Paradise No. 9 Mine. 

ORDER


Wherefore, pursuant to the authority delegated by the Secretary of Labor to the Administrator for Coal Mine Safety and Health, and pursuant to Section 101(c) of the Federal Mine Safety and Health Act of 1977, 30 U.S.C., sec. 811(c), it is ordered that Ken American Resources Inc.'s Petition for Modification of the application of 30 CFR 75.1909(b)(6) in the Paradise No. 9 Mine is hereby: 

GRANTED, conditioned upon compliance with the following terms and conditions: 

1. This Proposed Decision and Order is limited in application to the DAPCO, Serial No. 001 grader(s) powered by an Deutz diesel engine Model #BF4M1012EC, which has 6 wheels. 

2. The maximum speed on the diesel graders shall be limited to 10 mph by:

(a) permanently blocking out the gear(s) or any gear ratio(s) that provide higher speeds. The device must limit the vehicle speed in both forward and reverse; and 

(b) using transmission(s) and differential(s) geared in accordance with the equipment manufacturer which limits the maximum speed to 10 mph.

3. Prior to implementing the alternative method:

(1) the diesel grader(s) must be inspected by MSHA to determine compliance with the terms and conditions of the Proposed Decision and Order; 

(2) grader operators must be trained to recognize appropriate levels of speed for different road conditions and slopes; 

(3) grader operators must be trained to lower the grader blade to provide additional stopping capability in emergencies to stop the grader(s) within 4 seconds; and 

(4) grader operators must be trained to recognize the transmission gear blocking device and its proper application and requirements.

4. The grader must comply with all other applicable requirements of the Federal Mine Safety and Health Act of 1977 and the applicable requirements of 30 CFR, Parts 75 and 77. 

5. Within 60 days after this Proposed Decision and Order becomes final, the Petitioner must submit proposed revisions for its approved 30 CFR Part 48 training plan to the Coal Mine Safety and Health District Manager. These revisions must specify initial and refresher training regarding the terms and conditions stated in the Proposed Decision and Order. 

Any party to this action desiring a hearing on this matter must file in accordance with 30 CFR 44.14, within 30 days. The request for hearing must be filed with the Administrator for Coal Mine Safety and Health, 1100 Wilson Boulevard, Arlington, Virginia 22209-3939. 

If a hearing is requested, the request must contain a concise summary of position on the issues of fact or law desired to be raised by the party requesting the hearing, including specific objections to the proposed decision. A party other than Petitioner who has requested a hearing must also comment upon all issues of fact or law presented in the petition, and any party to
this action requesting a hearing may indicate a desired hearing site. If no request for a hearing is filed within 30 days after service thereof, the Decision and Order will become final and must be posted by the operator on the mine bulletin board at the mine.

 

 

_________________________________

John F. Langton
Acting Deputy Administrator
 for Coal Mine Safety and Health